Battery Isolator Cut Off Terminal with Bridging Fuse Holder. 

ADD A SECURITY LAYER TO YOUR VEHICLE! 

Green tightening wheel for quick electrical disconnection.

Simply remove the negative lead from batery, bolt the switch to the negative battery post and reconnect the battery lead to the post on the end of the switch. 

Suitable for both diesel and petrol engines. 

Zinc copper plated, 86mm x 36mm

Colour of fuse holder may vary. 

The Original Product - The Boost Ring® - Another performance mod for your Land Rover 200 or 300 tdi engine.

This little ring drops into your fuel pump giving you mid range performance gains on your diesel engine. Fitting takes just a few minutes.

Full installation video Below

Worldwide Shipping

This spacer ring allows more travel on the control piston for the timing advance within the fuel pump. This allows slightly more advanced timing at higher revs, allowing the power to remain longer before it flattens out at the top end.

This means a stronger pulling engine.

This is a tuning product. By fitting this, you will elevate the level of tune in your engine. Running higher cylinder pressures will expose any engine weaknesses. Fit this product entirely at your own risk. We recommend fitting an "Exhaust Gas Temperature" guage so that you can monitor your engine and react accordingly.

Kit contains:

• Boost Ring® -  200Tdi & 300Tdi
• High quality Seal - NBR 'Fuel Grade' Nitrile Rubber
• Replacement Screws
• Shims

Brake Disc Piston Pad Spreader / Separator

Professional Brake Calliper, heavy duty quality product

Perfect for your Land Rover

• Use with tommy bar fitted or 1/2" drive ratchet or spanner
• an essential tool for the removal and installation of new brake pads
• suitable for most ate / bendix / delco & girling callipers

It is easy to damage a brake pipe whilst off roading.

The brake lines on your vehicle can corrode quickly leading to MOT failure.

This little tool helps you make replacement brake pipes.

Small Handheld Brake PIpe bender for intricate bending

Ideal for making up replacement brake pipes in copper.

• 3mm
• 4mm
• 6mm dia.

Flare Ring Spanner Set 8 9 10 & 11mm

Ideal for the toolkit when working on brake pipes.

• Split / Flare Ring Spanner. Ideal For Working In Confined Spaces
• Flare Ring Spanner allows Access Over The Pipe Then Lower Down On To The fastner.
• Slips On to the pipe with ease without it being to slack.
• 8 & 9mm - 125mm Long.
• 10 & 11mm - 139mm Long.
• Drop Forged
• Nylon Storage Pouch. 

High quality zinc plated Spring Bolt with lock back action. 

Suitable for securing drawers, tables, doors, tailgates on your Overland Vehicle, Campervan, Horsebox, Boat or Trailer.

Also useful for securing shed doors, gates or lorry doors. 

Zinc plated for rust prevention. 

Approx Plate Length 72mm

Approx Plate width 40mm

Carlube Multi-Purpose Copper Anti?Seize Grease is a high melting point, lead free copper based assembly compound which forms a dense protective coating that will not wash or burn off.  Its anti-seize properties are particularly useful when assembly and dismantling occurs. Carlube Multi-Purpose Copper Anti?Seize Grease is ideal for protecting all metal against seizure, Leakage of oil and water, rust and corrosion, it can also help to prevent disc brake squeal if applied to calliper and BACK of disc pads, suitable for use on your battery terminals and connectors to aid current flow and help prevent sulphate buildup.

Land Rover Puma Defender

Clutch alignment tool.

Engineered to hold the clutch friction plate centered on the flywheel while fitting the clutch cover plate.

Suitable for Land Rover Puma Defender, fitted with 'Duratorq' engines.

• Large LCD display with LED/audible alarm indicating achieved and target torque levels.
• Selectable readings in Nm, lb.ft, lb.in, kg.cm or kg.m and accurate to +/-2% of stated capacity.
• Use as a calibration devise for existing torque wrenches. Supplied with  battery and storage case.
• Made by professionals for professionals! Specification
•  1/2" drive • Accuracy +/-2% • Memory holds up to to 50 readings • Range: 40-200 Nm (29.5-147.5 lb-ft)
• Large LCD display with LED and audio notification when reaching specified torque  
• Selectable readings in Nm, lb.ft, lb.in, kg.cm or kg.m  
• peak and trace settings 
• Auto shut off after 80 seconds to save battery life  
• Battery life: 55 hours of continuous operation 
• Dimensions: 75mm x 45mm (L x W)

• Included • Digital torque adapter • 1 x CR2032 • Storage case • Instruction manual

RIVNUT TOOL HEAVY DUTY - ECLIPSE - SPIRALUX 

Rivnuts are a quick and easy way of creating a threaded hole in sheet materials

• The heavy duty head is perfect for threaded rivets M3 M4 M5 M6 & M8 capacity
• interchangeable mandrels for M3 M4 M5 M6 & M8
• It is suitable for sheet metal, plastic and fibreglass.
• Quality rivnut setting tool by English Manufacturer Eclipse.

Package includes

1 x Insert Tool.
5 x Nose Bush/Mandrels: 3,4, 5, 6, 8 mm.

1x Mandrel Spanner

1x Vinyl Wallet