Flare Ring Spanner Set 8 9 10 & 11mm

Ideal for the toolkit when working on brake pipes.

• Split / Flare Ring Spanner. Ideal For Working In Confined Spaces
• Flare Ring Spanner allows Access Over The Pipe Then Lower Down On To The fastner.
• Slips On to the pipe with ease without it being to slack.
• 8 & 9mm - 125mm Long.
• 10 & 11mm - 139mm Long.
• Drop Forged
• Nylon Storage Pouch. 

Single USB Car adapter

12v or 24v Input

5v 1000mah output 

suitable for satnavs, phones and tablets

Land Rover 200 & 300 Static Timing Indicator Tool

This kit enables you to set the timing very accuratley on your Fuel injector pump.

if you are changing the timing belt, or have removed and refit the pump, the static method of timing the pump is the most accurate.

A video on how to do it can be found here

  AST 4398G

The Original Product - The Boost Ring® - Another performance mod for your Land Rover 200 or 300 tdi engine.

This little ring drops into your fuel pump giving you mid range performance gains on your diesel engine. Fitting takes just a few minutes.

Full installation video Below

Worldwide Shipping

This spacer ring allows more travel on the control piston for the timing advance within the fuel pump. This allows slightly more advanced timing at higher revs, allowing the power to remain longer before it flattens out at the top end.

This means a stronger pulling engine.

This is a tuning product. By fitting this, you will elevate the level of tune in your engine. Running higher cylinder pressures will expose any engine weaknesses. Fit this product entirely at your own risk. We recommend fitting an "Exhaust Gas Temperature" guage so that you can monitor your engine and react accordingly.

Kit contains:

• Boost Ring® -  200Tdi & 300Tdi
• High quality Seal - NBR 'Fuel Grade' Nitrile Rubber
• Replacement Screws
• Shims

A new Boost Pin to our range! The Fourby Boost Pin is made exclusively for us in the UK. 

We have been working with our suppliers, to bring to you a rival boost pin but with a mid range price point. 

Machined to give the same performance as the Morgan Hill pin and fully hardened to the spec of the original Bosch Pin. 

Remember this is a performance product and is fitted at your own risk. 

Land Rover Discovery 2 Td5 or V8 Key Shell, blank Blade, and genuine refurbished Valeo Chip. 

The chip requires programming to your vehicle. This should be done using a Nanocom, at your local specialist garage or Main Dealer. 

The blade is blank, ready to be cut by your chosen key cutter. 

Programing Barcode

Universal Drive Flange Holding Tool

Designed by Fourby, this is the alternative to the Land Rover tool LRT-51-003.

Essential tool for changing weeping oil seals, handbrake cables, diff rebuilds

Suitable for holding all common Land Rover drive shaft flanges, both transfer box output and diff input. The tool restrains the pinion flange, allowing the removal of the flange retaining nut or bolt.

• Hole patterns for: Disco 1 and 2, standard Defender and three bolt rear diff input. 
• Discovery TD5 front crank damper and output flange
• Includes a hole at 1ft from axis of rotation, for use with a spring balance. for setting torque pre-load on differential pinion bearings.
• Includes a square hole at the base of the tool to allow an extension using a breaker bar.
• 15mm Hex for 300tdi belt tensioner

High Lift or Farm Jack Spare wheel mount bracket
 

Fits Discovery 2 wheel pattern

A quality alloy bracket, beautifully manufactured. 

Bolts onto the rear spare wheel carrier, to hold the high lift jack.

Adjustable reach

Can be locked with a suitable locking device (not supplied)

This great item solves all your problems of where to store the High lift, and to quickly and easily remove the jack

For steel wheels

Land of Rope & Glory!

A genuine dyneema in red, white & blue rope.

10mm and 100ft. 

The perfect accesory to your winch!