Land Rover 200 & 300 Static Timing Indicator Tool

This kit enables you to set the timing very accuratley on your Fuel injector pump.

if you are changing the timing belt, or have removed and refit the pump, the static method of timing the pump is the most accurate.

A video on how to do it can be found here

  AST 4398G

The Original Product - The Boost Ring® - Another performance mod for your Land Rover 200 or 300 tdi engine.

This little ring drops into your fuel pump giving you mid range performance gains on your diesel engine. Fitting takes just a few minutes.

Full installation video Below

Worldwide Shipping

This spacer ring allows more travel on the control piston for the timing advance within the fuel pump. This allows slightly more advanced timing at higher revs, allowing the power to remain longer before it flattens out at the top end.

This means a stronger pulling engine.

This is a tuning product. By fitting this, you will elevate the level of tune in your engine. Running higher cylinder pressures will expose any engine weaknesses. Fit this product entirely at your own risk. We recommend fitting an "Exhaust Gas Temperature" guage so that you can monitor your engine and react accordingly.

Kit contains:

• Boost Ring® -  200Tdi & 300Tdi
• High quality Seal - NBR 'Fuel Grade' Nitrile Rubber
• Replacement Screws
• Shims

A new Boost Pin to our range! The Fourby Boost Pin is made exclusively for us in the UK. 

We have been working with our suppliers, to bring to you a rival boost pin but with a mid range price point. 

Machined to give the same performance as the Morgan Hill pin and fully hardened to the spec of the original Bosch Pin. 

Remember this is a performance product and is fitted at your own risk. 

Universal Drive Flange Holding Tool

Designed by Fourby, this is the alternative to the Land Rover tool LRT-51-003.

Essential tool for changing weeping oil seals, handbrake cables, diff rebuilds

Suitable for holding all common Land Rover drive shaft flanges, both transfer box output and diff input. The tool restrains the pinion flange, allowing the removal of the flange retaining nut or bolt.

• Hole patterns for: Disco 1 and 2, standard Defender and three bolt rear diff input. 
• Discovery TD5 front crank damper and output flange
• Includes a hole at 1ft from axis of rotation, for use with a spring balance. for setting torque pre-load on differential pinion bearings.
• Includes a square hole at the base of the tool to allow an extension using a breaker bar.
• 15mm Hex for 300tdi belt tensioner

Emergency 6 Tyre Traction Cable Ties for Wheels

Tie Length - 900mm
For alloy and aluminium rims up to 22in

Fully adjustable to fit any tyre size

Easy to install even while your vehicle is stuck in the snow, mud or ice. 

NOT designed for driving long distances
Only for use when your vehicle is stuck and driven for 5-10 car lengths or until you are safe. 

A great little gift for the car enthusiast in your life! Complete with stainless steel funnel.....

Available in Black, Blue, Green or Silver.

Stainless Steel Hip Flask:

Capacity: 5oz

Size: approx. 9.5 x 7.5 x 2.5cm (H x W x T)

Land Rover 200/300 Tdi Tuning Package 

With this combination of tuning products, you can add an extra 25% output power to your engine.

The complete kit contains:

• 1x Fourby Boost Pin
• 1x Fourby Boost Ring ®
• 1x Fourby Turbo Boost Controller

Fits all 200 or 300 Tdi's: Defender, Discovery, Range Rover.

These are performance upgrades. They will transform the output power of your engine. Fitting to your engine is at your own risk. 

Each item is available to purchase seperately. 

Turbo Boost Controller for 200 / 300 TDi Engines

Full Installation kit designed in house for Tdi engines, everything you need is in the pack.

Simple 15 minute fit for awesome extra power..!

This kit allows you full control over your turbo charger, allows you to dial in the boost to just the right amount to suit your fueling.

KIt contains:

• Boost Controller
• High pressure pneumatic pipe
• Silicone Pipe 
• High quality replacement spring clips
• Installation Instructions

Completly transform your ride, add this Fourby Boost Control kit with a Fourby Boost Ring and a Fourby Boost pin (also available to buy as a complete Tuning Package).

This is a tuning product, install at your own risk.

*Colours of pipe and Boost Controller may vary. 

50" 288W Curved LED Lightbar

This 288w, 96 diode bar is housed in protective die-cast aluminium casing and features a toughened Polycarbonate lens, for ultimate protection. 

As well as being dust proof this light also has an IP67 rating, making it suitable for a variety of applications and environments. 

Specifications:
288W 
10-30v DC
Waterproof Rating IP67
96x LED High Intensity LED's
20160 Lumen
6000/6500k Colour Temperature
Diecast Aluminium Housing
Polycarbonate Lens
Flood/Spot Light Beam
30000 Hours Lifetime 
Includes Fixings 

Dimensions:
1278 x 99 x 125(mm)